- Maiking a Windows Boot CD for my Computer
- Posted by Ron.... on April 29th, 2006
How would I make a windows boot CD for my computer.
I just purchased a new computer and it a HP that has the drive
partitioned and the restore is on a partition - Can I make a Boot
CD because those restore partitions only work if you can boot the
computer up...
Thanks
- Posted by ByTor on April 29th, 2006
In article <uJk#WN4aGHA.3992@TK2MSFTNGP05.phx.gbl>,
contactmethroughthe@newsgropus.com, Ron.... says...
There should be an option in the programs menu to create a full restore
CD.....Off the top of my head I can't remember the name of the
item.....Unless they stopped doing this?
- Posted by Milt on April 29th, 2006
http://www.bootdisk.com/
Milt
"Ron...." wrote:
- Posted by Malke on April 29th, 2006
Ron.... wrote:
Look in the Start Menu under HP and you will see where you can make a
Recovery Disk set. It is wise to do this.
Malke
--
MS-MVP Windows User/Shell
Elephant Boy Computers
www.elephantboycomputers.com
"Don't Panic"
- Posted by Bruce Chambers on April 29th, 2006
Ron.... wrote:
There's an option on the Start Menu to create a Recovery disk for the
computer.
--
Bruce Chambers
Help us help you:
http://dts-l.org/goodpost.htm
http://www.catb.org/~esr/faqs/smart-questions.html
They that can give up essential liberty to obtain a little temporary
safety deserve neither liberty nor safety. -Benjamin Franklin
- Posted by Richard Urban on April 29th, 2006
Over the years people have begun to call the whole process of getting into
Windows the "boot" process, but it is technically a combination of the "boot
process" and the Windows startup process, which occurs after the boot
process has completed!
The computers boot process is entirely controlled by the computer bios, and
is on the bios chip. When the boot process affirms that all hardware is
functional, the bios points to the Windows startup files located on the hard
drive, and Windows startup continues from there.
If the computer will not boot it is because there are hardware anomalies and
the bios halts the boot process - usually with an error message of white
text on a black screen. If this occurs, there is not a floppy or CD boot
disk in the world that will allow you to repair/start Windows.
If the boot process concludes successfully, and Windows does not load - then
a so-called "boot" floppy or CD (depending on what operating system you are
currently using) will allow you to possibly repair problems in the operating
system.
--
Regards,
Richard Urban
Microsoft MVP Windows Shell/User
Quote from George Ankner:
If you knew as much as you think you know,
You would realize that you don't know what you thought you knew!
"Ron...." <contactmethroughthe@newsgropus.com> wrote in message
news:uJk%23WN4aGHA.3992@TK2MSFTNGP05.phx.gbl...
- Posted by NoNoBadDog! on April 29th, 2006
"Ron...." <contactmethroughthe@newsgropus.com> wrote in message
news:uJk%23WN4aGHA.3992@TK2MSFTNGP05.phx.gbl...
There is an entire page of the manual devoted to this.
The Quick start guide has an entire panel devoted to this.
How did you miss all of that?
Bobby
- Posted by Sharon F on May 1st, 2006
On Sat, 29 Apr 2006 07:52:06 -0400, Ron.... wrote:
I don't have an HP but from reading these newsgroups, I get the impression
that HP has tied one of the Function keys to getting the Restore/Recovery
to run. In other words, pressing F<something> you get a menu asking if you
want to recover to factory state or try a non-destructive recovery. Check
your system manual for more details.
NOTE: This separate feature of their recovery system is in addition to the
set of recovery disks that the others are referring to. If hard drive
fails, the recovery partition with the fancy access method will be entirely
out of reach. If that happens, you'll be glad that you also created the
needed CD set.
--
Sharon F
MS-MVP ~ Windows Shell/User
