- P2 chip and fan
- Posted by Rich on September 5th, 2004
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi
Can any remember about installing a P2 266 slot one chip. Just built
a new P2 266 system from old left overs. The parts haven't been used
in years but suprising all work OK.
On the P2 chip there is just a large heat sink but no fan. I can't
remember if the chip ever had a fan. Would the heat sink alone be OK
or do I need a fan?
My main aim is to just run Linux on a quiet machine, so no fan would
be ideal.
Thanks.
Rich
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0.3
Comment: http://rich-ward.is-a-geek.com
iQA/AwUBQTr6fMjtolcV0LnqEQLvwgCfX/VkVzes/MmBWk3V/OlZ55Wb6n0An3bi
x2P1gjSzV2i1f3gph8RupaVx
=0357
-----END PGP SIGNATURE-----
- Posted by Chris Stolworthy on September 5th, 2004
<SNIP>
You don't need a fan for a P2. In fact if I recall technicall you almost
don't even need a heatsink....
-Chris
- Posted by Rich on September 5th, 2004
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Thanks for confirming it.
On Sun, 5 Sep 2004 07:35:07 -0600, "Chris Stolworthy"
<cstolworthy12@*remove*cableone.net> wrote:
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0.3
Comment: http://rich-ward.is-a-geek.com
iQA/AwUBQTsw3cjtolcV0LnqEQIUWgCfW84DXo/6wOWryzmtmJxDBkCHWD4An10H
ldYXRCplcKEP892ZxqIr2B9M
=igET
-----END PGP SIGNATURE-----
- Posted by kony on September 5th, 2004
On Sun, 5 Sep 2004 07:35:07 -0600, "Chris Stolworthy"
<cstolworthy12@*remove*cableone.net> wrote:
NO, you do need either a fan or a relatively large passive
heatsink and chassis with airflow routed through that passive
'sink.
You must be thinking of Pentium 1, P2 Klamath (233-300MHz) were
much hotter running. That's not to say it's hard to cool them,
but they're not the chips you're thinking of.
- Posted by DaveW on September 5th, 2004
You need a fan.
--
DaveW
"Rich" <richward@despammed.com> wrote in message
news:ibulj01p0fquetpjjg87j519gitsap6bvt@4ax.com...
- Posted by Hamman on September 5th, 2004
"Rich" <richward@despammed.com> wrote in message
news:ibulj01p0fquetpjjg87j519gitsap6bvt@4ax.com...
Early P2's REQUIRE A HEATSINK AND FAN
later ones can get away with just a large passive heatsink, and a good case
airflow.
I have a dual 233 system, and the chips in that get really hot [too hot to
touch] with an 120mm fan next to them
hamman
- Posted by Skeleton Man on September 6th, 2004
Just about all retail P2's I've seen came sealed in a plastic sleeve with
hs/f integrated (including mine).
The only time I've seen them with just a large heatsink is in OEM systems
such as compaq deskpro's (I have 3 of em @ work like that.. between 300Mhz
and 400Mhz.. they don't even have a case fan..).
If yours has a bare heatsink, then I doubt it needs a fan on it..
Regards,
Chris
- Posted by Rich on September 7th, 2004
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi
Its been running now for almost 48 hours with no problems. The noise
difference is amazing. Although I have noticed that the PSU power
supply is blowing air onto the fan area with I suppose does help.
FreeBSD on a P266 is bloodly fast.
Thanks.
Rich
-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0.3
Comment: http://rich-ward.is-a-geek.com
iQA/AwUBQT33ysjtolcV0LnqEQLibwCgyC3h7KxYT+cQ+XP18KPUKc cP0SQAoJLI
wAhzmjOaG0uWN+vin9gBlI+y
=MIQz
-----END PGP SIGNATURE-----
- Posted by ~misfit~ on September 7th, 2004
kony wrote:
Agreed. I have a Klamath 233 (2.8 vcore) that runs quite hot, it was
originally in a Compaq so has no fan attached (originally had a case fan
blowing at it). I swapped it out for a 450 Deschutes (2.0 vcore), same
set-up, passive sink out of a Compaq, same size sink, and it runs cooler. I
have a fan set up blowing over the thing, wouldn't run it without unless the
case was a wind-tunnel with the air-flow in line with the fins on the sink.
--
~misfit~
