- SATA disk, slow?
- Posted by Tomaz Koritnik on June 4th, 2004
Hi
I just bought computer with Gigabyte 7N400 PRO2 (nForce2 and SATA)
motherboard, Athlon XP2400+ and 80GB SATA 7200rpm Seagate Baracuda disk. I
also have one older 80GB Maxtor 7200rpm ATA100 disk. The problem is when I
test disk performance of both disks. I made program that writes and reads
to/from 200MB file but I also tested copying files with windows explorer.
SATA disk can write approx 35-40MB/s and read 17MB/s, while ATA100 does
40MB/s read, 21MB/s write. In all tests ATA 100 is little faster than SATA.
I can even see the progress bar going faster when reading/writing from/to
ATA 100 drive. Isn't this odd that ATA 100 is faster? Shouldn't SATA be much
faster than that? I use Windows XP with SP1 and I don't have fragmanted
disk. Shouldn't SATA write with 80MB/s or it's just my imagination?
regards
Tomaz
- Posted by Gerard Bok on June 5th, 2004
On Fri, 4 Jun 2004 18:26:58 +0200, "Tomaz Koritnik"
<nospam@nospam.com> wrote:
Sorry to say: yes, that's your imagination :-)
You are very unlikely to generate and/or accept 80 MB/s on an
Athlon 2400+ :-)
What you are looking at is not ATA vs SATA performance but the
limits of your system and the fact that it is probably better
optimized for ATA than for SATA.
--
Kind regards,
Gerard Bok
- Posted by kony on June 5th, 2004
On Sat, 05 Jun 2004 11:44:58 GMT, bok118@zonnet.nl (Gerard Bok) wrote:
The "Athlon 2400+" part isn't really relevant though, rather that
particular motherboard has SATA via a controller sitting on the PCI bus,
an additional bottleneck and latency.
On the other hand, an SATA 7K2 Seagate drive simply isn't capable of
80MB/s no matter what the situation, unless you're only considering a very
small, cached access. Then again, the Maxtor drive may just be a faster
drive, period.
- Posted by Tomaz Koritnik on June 5th, 2004
Hi
How large are speed diferences with SATA for Seagate, Maxtor and WD
disks? Do you have any approximate rates for them?
regards
Tomaz
"kony" <spam@spam.com> wrote in message
news:20k3c09pjhq274j0d1e14hkn41esn5ma2h@4ax.com...
- Posted by VWWall on June 5th, 2004
Tomaz Koritnik wrote:
The present SATA drives use essentialy the same mechanical drive
mechanism as the previous 7200 RPM ATA versions. Although the SATA
interface can pass 150MHz, no present drive can output at that rate.
The 10,000 RPM WD Raptor would have the highest output, but this is more
due to its rotational speed rather than to the SATA configuration.
SATA is still a good choice, if only for the smaller cables and lack of
master/slave confusion.
Virg Wall
--
A foolish consistency is the
hobgoblin of little minds,........
Ralph Waldo Emerson
(Microsoft programmer's manual.)
- Posted by kony on June 6th, 2004
On Sat, 5 Jun 2004 19:45:54 +0200, "Tomaz Koritnik" <nospam@nospam.com>
wrote:
Specific drive models would need to be considered, a Google search for
benchmarks (of those specific models) is the best way to find *current*
information, though of course you'd need to also consider the motherboard,
SATA implementation... An Intel board with Southbridge-integral SATA would
be the optimal interface with a seperate chip or PCI card being the worse,
usually.
