Hi, I've recently purchased an Apple iMac and upgraded to broadband
from dial-up at the same time. The modem supplied by the internet
provider works fine, I am connected to it at the moment while I post
this. So the ADSL line works fine. However when I plug the ethernet
cable into the router I can't see it from my iMac, presumeably because
it's not set up yet? But even hard-wiring the router to the computer
doesn't work. The accompaning CD has a setup guide which only says to
try opening a browser window, and you should see a Netgear Welcome
Screen, ... but instead I get the page telling me I'm nt connected to
the internet.

Has anyone else got a Mac and tried using this Netgear router? If so
how did you do it? All the tutorials on the CD seem to be .exe files, I
am wondering if I should try and get hold of a PC to set up the router
and then once it's set up I can use my Mac - but I feel I shouldn't
have to do this. Any help much appreciated!

On 17 Sep 2006 09:28:41 -0700, t.d.russell2@googlemail.com wrote:

How's your network status?

Maybe this'll help - http://tinyurl.com/m7h2n

Good luck!

Penny <me3@privacy.net> wrote:


<snip>

This reply is nothing more than a male pornographic image.

Jim
--
Find me at http://www.ursaminorbeta.co.uk
AIM/iChatAV: JCAndrew2
Skype: greyarea

On Sun, 17 Sep 2006 18:00:53 +0100, jim@magrathea.plus.com (Jim) wrote:

What the hell's this turd-burglar on about?

CN

I've not used this model, but usually with Netgear stuff you need to go
to 192.168.0.1 to set them up. User name is admin, password is either
blank or 'password'

To get to this, you'll have to set the mac network manually for a bit -
use 255.255.255.0 as the subnet and 192.168.0.2 as your IP address. Put
192.168.0.1 as the router address.

Andrew



t.d.russell2@googlemail.com wrote:

On 17 Sep 2006 09:28:41 -0700, in uk.telecom.broadband ,
t.d.russell2@googlemail.com wrote:


You don't need a PC, the router is configured through the web
interface and is hardware-agnostic.

Your connections should get set up something like this.
NB I'm assuming your ADSL modem has ethernet output. If not, you have
the wrong kit.

Without any network cables attached, ensure the iMac is set to use
DHCP to get an IP address.

Then Power off EVERYTHING.
Connect ADSL modem to router's WAN port.
Connect iMac to one of the router's LAN ports with normal ethernet
cable.
Power the modem on. Wait around 30 secs.
Power router on. Wait around 30 secs.
Power the iMac on.
Check what the iMac's IP address is. If should be 192.168.x.y where x
and y are two numbers. I don't have OSX so I can't tell you precisely
how you do that, but on my Linux box I'd open a command window of some
sort and type 'ifconfig'.

If the address is 169.something then your router isn't talking to your
computer. Try a factory-reset (there's normally a handy button on the
side). If this fails, check the manual or user guide (maybe some PDF
on the CD) to see what the router's default address is. Set your iMac
to have a similar address - eg if your router is 192.168.x.y, set your
iMac to 192.168.x.y+1 (if y+1 > 255 then use y-1). Reboot hte iMac
after changing the address, just to be safe.



--
Mark McIntyre

On Sun, 17 Sep 2006 15:25:41 -0400, Mark McIntyre wrote
(in article <pi7rg2d4hsb00del2khmrtgf385mnl8gup@4ax.com>):

If the OP has a USB DSL device, he should get it replaced by an Ethernet
device ASAP. USB devices are nothing but trouble.

To do this, go to System Preferences/Network. Double-click on 'Built-in
Ethrnet'. You'll be presented with a dialog with several panes, the first
being 'TCP/IP'. By default the system is set to use DHCP. You can change this
if you wish at that pane. Note that some ISPs have problems with connections
if you don't type in the IP address of their (local) DNS server in the 'DNS
server' box. For example, Adelphia here in West Palm Beach gets flakey if I
don't have the WPB server IP entered. (68.168.1.42 in this case.) Entering
the IP for an Adelphia server elsewhere has bad results. Entering no IP has
worse results. You may want to talk to your ISP and get their DNS server IP.
You don't need a search domain and I usually leave that blank, but if you
want to you can simply type in the name of your ISP's primary site.
('adelphia.net' in my case.)

If you're using ADSL, odds are that you're using either PPPoA or PPPoE. if
PPPoA, you don't need to do anything. If PPPoE you need to configure _EITHER_
the Mac or the router. Don't do both. Very bad things will happen if you try.
Note that if you configure the Mac, you'll have to configure any other
computer which you attach to the local net and which you want to have
Internet access, so it's easier to configure the router. To configure PPPoE
on a Mac, click on the 'PPPoE' pane next to the 'TCP/IP' pane in 'System
Preferences/Network'. You'll be presented with a dialog requesting the
required informtion.

If you got your DSL device from your ISP, odds are that it's already
configured for PPPoA or PPPoE and you don't need to do anything more.

I don't know if any ISP in the UK uses PPPoE. The only ISP I dealt with which
used DSL in the UK used PPPoA. (They tried to dump one of those 'green
stingray' (since then replaced by a 'purple stingray' which was equally
useless) Alcatel USB things on me. I went and bought an Ethernet unit
instead. I've still got it in a closet somewhere around here, though it's
rather useless without a trans-Atlantic cable, Yankee DSL uses PPPoE not
PPPoA.)

Typically you'll see a lot of little lights blinking furiously away on the
router and DSL device. When things have quieted down, the devices are ready.

Some DSL device/router combinations (Alcatel Speedtouch, I'm referring to
_you_) use 10.x.x.y where 'x' is 0 to 255 and 'y' is 0 to 254 instead. Some
routers (Apple AirPort routers, I'm referring to _you_) do the same.

On Macs you can get the info from System Preferences/Network; the initial
dialog, before you double click on 'built-in ethernet', announces what IP the
port has been assigned. Once you double-click on 'built-in ethernet' the IP
info is displayed.

You can also launch Terminal, and type 'ifconfig'.



--
email to oshea dot j dot j at gmail dot com.