hi Chuck, I do not want to use TFTP as i will eventually need to write a customised program to do this. Let me extend my question further. 1) Are there any examples available or could anybody...

hello: thank you, thank you. i did a lot of research on the problem and filed bugs in GCC bugzilla as well as on Mikrocontroller.net. pls see these links for more information: - GCC Bugzilla Bug...

On Mon, 07 Jul 2008 13:53:32 -0500, Grant Edwards <grante@visi.com> wrote: And what would a flimsy signal ground wire help to reduce the common mode voltage in mains powered systems ? To...

On Fri, 4 Jul 2008 15:45:54 -0700 (PDT), larwe <zwsdotcom@gmail.com> wrote: I hate to burst your bubble, but whipping out any computer device in a bar is NOT cool. ;)

svyamuna wrote: http://en.wikipedia.org/wiki/RS-232#Voltage_levels -- Frank Buss, fb@frank-buss.de http://www.frank-buss.de, http://www.it4-systems.de

Jack Klein wrote: And, with a few discrete macros, they work just fine for a 64180 (or Z180) etc. One of the advantages of the CLI. -- : Chuck F (cbfalconer at maineline dot net) :...

DC wrote: I know exactly what it is. Pure unobtanium. The 'SC' prefix is a proprietary marking for a big OEM customer, so the only way to get information is to squeeze it out of that...

gEDA (http://www.geda.seul.org/) seems to be the best (true) open-source package I have used. Pretty much Linux based though... "Roger_the_Dodger" <cresswellavenue@talktalk.net> wrote in...

I'm lokking for a small (4x6", 6x8", range) SBC that has a reasonably good A/D converter (100+MSPS), at least one 1G ethernet, and one or more SATA-2 ports. I'm not picky about the processor....

On Jul 4, 8:28 pm, Scott in SoCal <scottenazt...@yahoo.com> wrote: It could be Freescale HCS12 (or perhaps HCS08, but not sure about that) BDM connector. For the HCS12, Pin 2 would be ground, pin...

On Jul 5, 9:39 am, langw...@fonz.dk wrote: It could very well be a six pin BDM header from a freescale HCS12 or (not sure about this) HCS08. What pins of the header are connected to power or...

msg wrote: You could do it all with a BasicX-24 http://www.basicx.com/ ] $99.95 for the chip plus development kit, and it is very esy to bang out code for one-off projects like yours. -- Guy...

msg wrote: Modern OS's (even windows) do not thrash unless you try to run too much with too little ram. And yes, if you have a larger disk to spread the writes, then there will be fewer...

On 2008-07-07, David Kelly <n4hhe@Yahoo.com> wrote: By default, does that compare against HEAD or against the revision that was checked out? -- Grant Edwards grante ...

On Jul 7, 1:15 pm, "Pete Fraser" <pfra...@covad.net> wrote: Hi Pete, I was trying a new ftp application and corrupted the website. Please try again and let me know if you have any problems. -Dan

The examples can be downloaded at msp430.com, in the Code Examples tab. However, using the MSP430 as a spi master: I have found it best to onl use the RX ISR, and leave the transmit interrupt...

Do you know what's the Rigol model Agilent is selling as its own? I'd lik to know if I could rely on Agilent's 3000 model support files (firmware an stuff) after I've bought the equivalent Rigol...

Tiffany 925 silver jewelry, jewelry tiffany, jewelry discount tiffany, jewelry store tiffany, Discount MP3 players, MP4 players, Nokia N95 Mobile Phone, GPS, IPOD NANO, china Supply. Discount Coach...

Hello, I am developing 8051 based vehicle tracking system and Need SOS help o the following: Assemblly language code for transmitting "SMS" through AT command fro 8051 to GSM module. thanks in...

Rich Webb wrote: Now the question is: do these constraints apply before, or after the semantics of 6.3.16.1 (C99: 6.5.16.1) have been taken care of? These semantics are: In simple assignment (=),...