Hi,

I am testing IAR Kickstart to program MSP430 EasyWeb3 board .
I want to program and debug this board by using MSP430-JTAG (cost 14.95
$) from
http://www.sparkfun.com/commerce/pro...products_id=15

But I only found MSP-FET tools for debug, how can I configure to debug
and program with this MSP430-JTAG on my board

Regards,
nyt2005

In article <1141473472.840592.218000@i39g2000cwa.googlegroups .com>,
mgemb <nyt2005@gmail.com> writes
I think you will find that the best bet is the IAR J-link or the Segger
J-link which are not quite the same thing (though both made by Segger)

Unless your time is free writing the interface software in more trouble
than it is worth. Also you will have to uses the more limited RDI
interface.

--
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
\/\/\/\/\ Chris Hills Staffs England /\/\/\/\/
/\/\/ chris@phaedsys.org www.phaedsys.org \/\/\
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/

Thanks to Chris Hills

, but I found in the specifacation page of MSP430-JTAG that it can use
with IAR Kickstart,

Another problem is that, I also found that only 2k limit of C Code can
write in IAR Kickstart.
How i can overcome it. i am not expert in Asembly to change.

I have to try with hard MSPgcc or other good and cheap way available
?

Regards,
mgemb

On 4 Mar 2006 06:21:36 -0800, "mgemb" <nyt2005@gmail.com> wrote:

Only by buying a full license from IAR. Did that at work. Good compiler
but expensive and (at least at the time) updates need a current, paid-up
maintenance contract.

Another option is the ICC430 compiler from Imagecraft. Not free but not
expensive either, and quite easy/fast to get up and running. The
compiler's IDE supports the TI FET device and so, presumably, it would
work with the Sparkfun clone.
http://www.imagecraft.com/software/

--
Rich Webb Norfolk, VA

In article <1141482096.207898.75020@p10g2000cwp.googlegroups. com>, mgemb
<nyt2005@gmail.com> writes
That is because the Kickstart version is free. You could buy various
versions including the base line version which has a 12K limit for C
code.

1 Learn assembly. You should do this anyway. It is important to
understand the architecture and how it works with assembly even if
normally 99% of your work is in C

2 Buy the base line version not cheap but not expensive either for a
good quality compiler.


--
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
\/\/\/\/\ Chris Hills Staffs England /\/\/\/\/
/\/\/ chris@phaedsys.org www.phaedsys.org \/\/\
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/

On 2006-03-04, mgemb <nyt2005@gmail.com> wrote:

Anything that will work with the parallel port FET will work
with the Olimex one that sparkfun sells. Is that what you're
asking?

--
Grant Edwards
grante@visi.com

Thanks Grant Edwards,

I ask this. I know that MSP430-JTAG is also for Flash Emulation but IAR
has no model no match with MSP430 JTAG and only MSP-FETxxxxx nos so I
am not sure and asked this.

And as I mentioined , IAR's C code limit is so bad, and as suggested
above, I don't want to pay 100s of $$$ for IDE,

so i think i have to try on MspGcc at that case
where can i get good tutorials about mspgcc
especially for msp430
i found some, msp430.info and some, but just a little they explained..

Thanks Chris Hills and Rich Webb

Regards
mgemb

In article <1141541532.396856.23230@e56g2000cwe.googlegroups. com>, nyt
<naingye@gmail.com> writes
It is very good for a Free version of a commercial compiler. The full
compiler has no limit.

You are not paying for an IDE but a very good compiler.


--
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
\/\/\/\/\ Chris Hills Staffs England /\/\/\/\/
/\/\/ chris@phaedsys.org www.phaedsys.org \/\/\
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/

nyt wrote:
ImageCraft's compiler is fully-functional for 45 days, then limited to
4k code. The licensed version is a lot cheaper than IAR, and the
support is excellent.

mspgcc is probably the most powerful and flexible C compiler available
for the msp430, and is certainly the best value for money in pure cash
terms (being free). But if you are not used to the world of gcc, you
might have to do a bit more thinking, learning, and website reading,
compared to the download-and-install ImageCraft compiler.

Thanks,

but Is ImageCraft fully support my board and my programmer
MSP430-JTAG(14.95$) parallel port JTAG from www.olimex.com ?

if so i will try ImageCraft first.

Regards,

nyt wrote:
The Olimex parallel port JTAG adaptor is functionally identical to the
TI MSP-FET. It's smaller and cheaper, but the software can't see that!