Hi all, I am using the Cypress FX2 to interface an FPGA to a PC via an USB2.0 link. The FX2 was configured to provide 4 bulk endpoints (+ synchronous FIFOs). Each bulk EP (2,4,6,8) is 512 byte...

Does anyone have suggestions/experience with using an 8-bit serial-in, parallel-out shift register like the 74HC164 to drive a LCD panel? I have been using a LCD module in 4bit mode, and want to try...

2006 IEEE Congress on Evolutionary Computation Sheraton Vancouver Wall Centre Vancouver, British Columbia, Canada 16-21 July 2006 Special Session on Hardware Architectures for Genetic, Neural and...

Hi We're trying to interface a PIC micro to an 8052 micro using the Parallel Slave Port on the PIC. The 8052 can read bytes written to it by the PIC ok, but when the 8052 writes to the PIC, the PIC...

Terje Mathisen wrote: I'm pretty much aware of the Bochs source available, but am more keen in understanding the concepts..so wud prefer a good document or a book if available

Hi All, Could you please help to comment this? http://www.avelink.com/bluetooth/index.htm Do you think it is worth to buy? Thank you very much! Best regards, Boki.

It has three rows of text printed on the back, and they are "TIOPA 690 3BZL9". I have this chip, but it was fixed to my board by some other people. Datasheet or any description that can help me is...

using: ImageCraft IDE v6.31 - ATMega64 One of the standard include files is "eeprom.h", included below. I am getting a compile error at the point marked with "#*#*". As you can see, this file does...

In Example_280xAdcSeqModeTest.c for the TMS320F2808 DSP i wonder what the following assembler command is for: asm(" RPT #11 || NOP"); In this source: // TI File $Revision: /main/5 $ // Checkin...

somebody helps me? if yes answer!! please!!

Does anyone know where I can get a touch screen durability tester? Something that will repeatedly tap or write over and over again to determine the life of the touch screen. Thanks, Nikyu

I am trying to interface to a truck's in-vehicle network using a legacy computer. I know nothing about in-vehicle network standards. We bought a Dearborn Group DPA III/i to communicate via a serial...

Hi, I want to buy a MPC555 evaluation board for my personal learning. One requirement is it should be usable with Linux/Gnu software as development platform. I see two boards at around...

Anyone has work with srf08 using cygnal F12X ? Need some help. I am need to both the up and the i2C Thank you

Hi, I am looking for a budgetary solution for a CAN bus tracer. All I really need to do is to display CAN messages on the PC as they are sent over the bus. Any hints? Thanks and regards Roland

Hello there ! I'm pretty much a newbie when it comes to finding and buying passive SMD components. So, I went off and started a project that uses some surface-mounted ICs, and these ICs now require...

I asked a question with subject "Voice Recorder?" a few days ago. http://groups.google.com/group/comp.arch.embedded/browse_thread/thread/edfdae3e27e614f3 But I can't explain the question (again :)...

I want to make a voice recorder using an MCU(8051 or PIC). The recording time doesn't matter at this time. I just want to learn how to digitalize inputted voice by a microphone and write it to...

Hello Newsgroup, In the data sheets of the Renesas R8C controllers some versions are listed with lower re-programming cycles for the flash than others. Some can be re-programmed 100 times, others...

To support various modules inside a machine. The likely architecture is a front end PC talking USB 2.0 to a Cypress FX2LP in the machine. That then splits the control work out to various nodes...