Hi. Is anyone aware of a GCC 4.0 for ARM release available in binary form? www.gnuarm.com doesn't seem to have GCC 4.0 Linux binaries, only Windows. Thank you. Richard.

MAKE THOUSANDS!!! I found this on a bulletin board and decided to try it: I don't care about the useless pre-fabricated crap this message usually says. All I say is, it works. Continue pre-fab...

Hi, In MSP430F1101A, How information memory differs from flash memory? In what way it is useful for a programmer? If anyone have any supporting documents related to this, please guid me. Thanks in...

Hi everyone I have been desing hardware based on the C51 architecture in assembly code I am wanting to migrate to ARM and and wanting to start writing in C rather than assembler. can anyone give me...

Hi, Have anyone built embedded device with these components?

Hi.. I'm trying to build my own PSTN-based home controller. Yes, I know that many would suggest to build IP-based one. The problem is subscribing internet here is far more expensive than...

Tried looking for documentations on working with the above lcd driver (or similar) but couldn't find it anywhere off the net. Wonder if anyone has worked with this before?

I may be somewhat off topic but i've ran into a mountain i cannot seem to get over regarding the hardware design of a switching mode power supply. I'm using an LM2585-ADJ simple switcher chip from...

Hi, I find that some of the very interesting features of PC-Lint (such as reporting cases of uninitialized variables, memory leaks, value tracking, array bounds check etc.) don't work as expected...

I need to drive a 5 volt ADC (LTC1863) to be able to use a Vref of 4.096 volts. The Vih of the ADC is 2.4 volts. The processor is a 3.3 volt xMOS with a Voh of 2.6 volts (measurements show it to be...

Hi, It seems that Taiyo Tuden has decided to openly sell their bluetooth modules without giving buyers the datasheets to use them. (just a simple overview 1-pager) This seems very strange to me. I...

I've bought some time ago 8051 learning kit with monitor in ROM and 8k external ram starting at 0x8000h, where programs in intel hex format are load to external RAM via RS232 if i want to start this...

I'm looking for an alternative connector for a serial port. I HATE the way the DB9 connector looks, but still want to do serial traffic over 5-10 feet. My app would have say a 100 devices and they...

In news:d8c5sa$mp9$1@nemesis.news.tpi.pl, zanxy@zanxy.com <zanxy@zanxy.com> typed: Check out http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3193 Karl Olsen

I need a whinge. Bloody Zilog's so-called ez80 software has been running me ragged for over a week. The code executes perfectly on the development kit, crashes on the target. Running off with the...

Hello, We are seeking a "light" algorithm performing exponential function (y=A*exp(-k*x)) fitting. A typical curve is composed of 200 16-bits integers. As the code should be executed by a MCU,...

I'm looking for a microcontroller with low speed USB 1.1 support in a DIP package, and with onboard Flash (ie: not a OTP chip). I know about the HC08 JB8. I also see that Microchip do a PIC one as...

I am looking for a device which can replace a floppy drive (3.5") with a solid-state memory and be pin-compatible so I can just plug it into the floppy ribbon cable and replace the floppy drive with...

Take a look at DataGet - it connects devices such as electronic calipers and laboratory instruments to the Palm. -- --------------------------------------------------------------------- DataGet &...

Hi Guys, Could anybody tell me how I can buy a cheap or even used Microcontroller programmer (M68HC12) and its necessary devices? I'm new into this and need your advice. Thanks