C A L L F O R P A P E R S WORK IN PROGRESS Session of RTSS 2004 The 25th IEEE International Real-Time Systems Symposium Lisbon, Portugal, December 5-8...

Hi, I am trying to get a ATMega8 and ATTiny26 to communicate over a two wire bus but can't get it to work properly. At this stage all I am trying to do is get the ATTiny26 (Slave Rx) to acknowledge...

Hello, iam developing monitor programe by using mc68332,in tornado C, here i need to write some data into EEPROM(at28hc256n). to do that iam maiantaining 3 files 1)bootrom. 2)my application file---> ...

Hi, I just need to get my facts straight. I have been given a spec, where the use of C++ and a '51 core MCU is mandatory. AFAIC a C++ compiler for the 51 does not exist. Regards Anton Erasmus

hi, im a newbie in DSP and embedded programming and i've some doubts that i hope some of you could kindly answer. i've to do some profiling between DSP and ASIC/FPGA solutions. Im a FPGA guy so im...

Yello, Can someone suggest a place for me to start in making my own embedded system? Like hardware requirements and stuff? I'm used to Linux so I'd probably use that as an operating system. I'm a...

Circadiant is a growing technology company that designs Optical Standards Testers for R&D and Manufacturing. We provide optical component and network equipment makers with...

Perhaps the wrong ng, but I know I'm amongst well-informed friends here, so please forgive me if so. I need to become an overnight expert in driving (smallish, DC) motors, with particular emphasis...

Hi all, I am a newbie in this, so please bear with me... I was asked to estimate various options of embedding Ethernet into our future board level products. Here is the list of some of the...

Hi, All Is any tutorial about embedded system development on NetBSD? Thanks and Regards Roger

Hello Can anybody suggest some "free" embedded software engineering tools? I am looking for tools that help in the design and documentation of embedded software and that are "not" UML-based. Thank you

Ignore, sudden anomaly on my connection. -- Chuck F (cbfalconer@yahoo.com) (cbfalconer@worldnet.att.net) Available for consulting/temporary embedded and systems. <http://cbfalconer.home.att.net> ...

Hi, Could anyone suggest a good book in processor architecture with software/programming approach? Thanks a million! Dan

Hi, for a low-cost design I need a small 8-bit microcontroller (1-2k Flash will do) and now the question is whether I need to plan for an external resonator or an internal oscillator is good enough....

Coulden't help but notice your application. http://www.multiview.net/vsi-pro.html UK http://www.americanvideoequipment.com/catalog/vsi-pro.htm US We interface to more cash registers than anybody...

Hi Everybody, I am working on RMAP protocol.I have a decoder which can decode RMAP and MIT protocol. This decoder works on RMAP protocol when the IR receiver is R3302,IR_REC_V_56KHz_TSOP2256VI1(not...

"Roger" <enquiries@rwconcepts.co.uk> wrote in message news:VlHUc.105$cb5.82@newsfe5-gui.ntli.net... CTS/RTS handshaking isn't used across the PSTN boundary. It is used between the modem and the DTE...

Hi, I have a need for an OSD generator IC/module with PAL output but I only seem to find references to the STV5370A which is obsolete. Anyone out there using a current product? I need to be able to...

Is there any software put out by Atmel (similar to FLIP) that will allow me flash RD2 or RC2 chips using a palm pilot. Can I use the Flip 2.4 for Palm (if one exists - hint Atmel this would be a...

Hello all Im new to using Atmel devices and AVR studio. We have built a project with avr-gcc and Im using AVR studio version 4.08 to debug. the device is the ATMEGA162. My problem is that we have...