What's the biggest serial memory? Have been using 32kb Ramtron chips. Needs 500kb and maybe more (lots of chips...). Uses a H8S2357 - using a parallell memory would waste a lot of pins and adds...

In article <3EFC53CF.76D1DAAF@earthlink.net>, Jack Crenshaw wrote: If you're talking about the format that IA32 FPs store values in memory, then I doubt it. If you're talking about the...

Hi, i am working with an Embedded Planet RPX MPC860 board and am totally new to embedded programming. All i want to do is verify the steps to compile some code and put it into the flash memory. I...

Michael, Start from here .. http://www.crowcroft.net/kitsrus/k180.pdf the follow the links. Good Luck Tom Woodrow www.dacworks.com

On Fri, 27 Jun 2003 14:23:22 GMT, Jack Crenshaw <jcrens@earthlink.net> wrote: Unless IEEE 794 is something new, I think you mean IEEE 754. With the proviso that the values of 0 and 255 for the...

Which Intel math coprocessor? 8087? 486? Pentium?

There is a chapter (Ch 6) on stream ciphers and LFSR's that would be relevant to you in this application in "Handbook of Applied Cryptography" by Menezes, Oorchot & Vanstone. Sorry all the details I...

"Craig Rodgers" <craig@student.usyd.edu.au> wrote in news:bdcak4$fc$1@spacebar.ucc.usyd.edu.au: Well if you can switch cores,...

Can someone point me to a URL showing a small schematic with a MMC Card (MultiMediaCard) connected to some IO pins of a microcontroller? Many thanks! Regards, -- Bernhard Roessmann

hello everyone Has anyone ever used any products by applied data systems? My company is thinking about partnering up w/ them to work with some of their embedded SBC development boards, but i kinda...

I've been assigned the task to provide alternatives and solutions to bringing legacy Ada 83 code to a new embedded system. The new system's hardware, OS and language of choice is fixed...

Hello all I have tested one of each of the above pics in a circuit which just lights a led on PortB,0 via a 470 ohm. The clock is a 4MHz crystal. Both stop working at 4.0V although the 'LF should...

On Thu, 26 Jun 2003 00:19:59 +1000, "Craig Rodgers" <craig@student.usyd.edu.au> wrote: Wiznet W3100A is a nice device. It runs the TCP/IP stack in hardware, hence the amount of code to write for a...

Craig Rodgers wrote: That's right, most of the 100Base-T chips are designed for the PCI Bus, but maybe this is what you want: LAN91C113I AX88796L Regards,

Hi, I am looking for a MPC564 (PowerPC) based development board that includes GNU tools with some examples for the board. It would also be great if it included a BDM device that can be used with GDB...

Hi all- I am new to embedded systems area. I have a question. I want an embedded system with the following specs. a) It should have an RF interface instead of Ethernet. b) It should be battery...

Hi, Need a bit of help with this one - Cant see what is wrong! I want to use both channels on the serial unit of the 80C186EB. When I receive data on channel 0, the RI bit is set and an interrupt...

There is a device out there that embeds a complete 10/100 interface, including a '186 micro, all the stacks etc into the Ethernet connector socket. Around AUS$75, probably around US$35. pricey, but...

Hi, I am excuting a project where a module involves measuring the water pressure in a pipe. I have a transducer to convert the pressure to electrial signal. I want a C code (that I will embed in a...

"Craig Rodgers" <craig@student.usyd.edu.au> wrote in message news:bdcak4$fc$1@spacebar.ucc.usyd.edu.au... The best one i have seen latey is the lantronix part that has the whole lot in one RJ-45...