- 3845 and l2tpv3 pseudowire problem
- Posted by Dmitry Melekhov on May 12th, 2008
Hello!
I have following configuration on cisco 3660 on one side :
l2tp-class sberbank
pseudowire-class eth-sberbank
encapsulation l2tpv3
protocol l2tpv3 sberbank
ip local interface Loopback0
interface Loopback0
ip address 192.168.200.249 255.255.255.252
interface FastEthernet0/0.4
description sberbank
encapsulation dot1Q 4
no cdp enable
xconnect 192.168.200.250 1 pw-class eth-sberbank
and mirror configuration on another side on 2801.
Now I want to migrate from 3660 to 3845.
l2tpv3 connection starts
p100-cr3845-2#sh l2tun
%No active L2F tunnels
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocID RemID Remote Name State Remote Address Port Sessions L2TP
Class/
VPDN
Group
37042 9051 xnet-cr2801-2 est 192.168.200.250 0 1
sberbank
LocID RemID TunID Username, Intf/ State Last Chg
Uniq ID
Vcid,
Circuit
11288 43070 37042 1, Gi0/0.4:4 est 00:00:06
2
but traffic don't pass.
I can see only arp requests pass this tunnel with tcpdump on both
sides.
What can be wrong?
- Posted by Merv on May 12th, 2008
1. The configurations wrt to the tunnel on the 3660 and 3845 are
identical ?
2. what is the IOS version in use on 3660 ?
3. what is the IOS version in use on 3845 ?
- Posted by Dmitry Melekhov on May 12th, 2008
On 12 อมส, 18:19, Merv <merv.hr...@rogers.com> wrote:
Yes, shure
btw, 2801 on another side runs 12.4.17a
- Posted by Merv on May 12th, 2008
On May 12, 1:12 pm, Dmitry Melekhov <d...@belkam.com> wrote:
Is CEF enabled on the 3845 ?
- Posted by Dmitry Melekhov on May 13th, 2008
On 12 อมส, 23:33, Merv <merv.hr...@rogers.com> wrote:
Yes, it is enabled.
Very strange thing is that arp requests pass (this mean that l2
connection exists), but other traffic not.
May be something is wrong with switches?
I don't phisically replaced 3660 with 3845, they both are connected
now.
But I tried to change connection from 2801 to 2811 on other side (they
are both connected too) and there are no problems...
- Posted by Dmitry Melekhov on May 13th, 2008
On 13 อมส, 07:21, Dmitry Melekhov <d...@belkam.com> wrote:
I tested, switches works OK, mac address from far point moves to 3845
when I turn loopback 0 no shutdown and shutdown on 3660...
- Posted by Merv on May 13th, 2008
On May 13, 1:00 am, Dmitry Melekhov <d...@belkam.com> wrote:
Are ARP replies being received ie. is the tunnel passing both
broadcast request and unicast response ?
Post
sh xconnect all detail
sh l2tun summary al
sh l2tun sess all
- Posted by Dmitry Melekhov on May 13th, 2008
On 13 อมส, 12:10, Merv <merv.hr...@rogers.com> wrote:
Just because I see mac addresses in arp tables on both sides I'm shure
that response pass.
There are no above commands . at least in 2.4.19...
L2TP Session Information Total tunnels 1 sessions 1
Session id 46479 is up, tunnel id 11028
Call serial number is 4900004
Remote tunnel name is xnet-cr2801-2
Internet address is 192.168.200.250
Session is L2TP signalled
Session state is established, time since change 00:08:36
964 Packets sent, 442 received
78038 Bytes sent, 30971 received
Last clearing of "show vpdn" counters never
Receive packets dropped:
out-of-order: 0
total: 0
Send packets dropped:
exceeded session MTU: 0
total: 0
Session vcid is 1
Session Layer 2 circuit, type is Ethernet Vlan, name is
GigabitEthernet0/0.4:4
Circuit state is UP
Remote session id is 43109, remote tunnel id 56034
DF bit off, ToS reflect disabled, ToS value 0, TTL value 255
No session cookie information available
UDP checksums are disabled
SSS switching enabled
Sequencing is off
Unique ID is 19
%No active PPTP tunnels
- Posted by Dmitry Melekhov on May 14th, 2008
On 13 อมส, 15:22, Dmitry Melekhov <d...@belkam.com> wrote:
well, I installed vtun on linux servers and shall try to forget about
cisco's buggy l2tpv3 ;-)
