Hello, Our router does not have the IPSec software on it and a client needs to use a VPN that needs IPSec. Is the only way to do this via IPSec software or could a normal PIX515E also do it somehow?

Hello, I have several Cisco 837 with standard IPSEC Vpn (done with SDM). I just want to know if there is a command to keep the tunnel up. When it's unused the tunnel drop. I try the crypto isakmp...

I have a situation requiring the redirection of all HTTP,POP3,and Imap requests to a specific address to another destination. This traffic is not crossing a firewall of any form, just from on...

We are currently looking into the performance of one of our gateway 3640routers running BGP with 2 FastEthernet connections. Current total bandwidth is peaking arround 7-8Mb av 5Mb and we are seeing...

I'm looking for more insight in cisco architecture internals... I'm doing a network class and I need to do a little study comparing software- and hardware routing. What I'm looking for is to what...

Hi! The Cisco Feature Navigator assures that 802.1q tunneling is aviable in the 2600, 3600 and 3700 series requiring a nm-16esw module. However, I have not found information about configuring this...

I have a Cisco 831 router at home. I have two PCs and a VOIP phone (HandyTone-286) plugged into the router. I am having some problems when calling Australia. As an old MCI central office person,...

Help. I have a PIX 525 which I have access via console terminal but I cannot access via http. Is the username "admin" correct? Isn't the enable password the same for the http access? If the http...

Hi, Recently I've bought Cisco WS-C1924-EN and I wonder if there is possibilty to form a trunk link to a Linux or FreeBSD box with ISL encapsulation. Unfortunately I don't have Cisco router which...

I'm trying to setup SNMP on our Cisco 2600 so I can create some MRTG graphs. I've installed perl & mrtg on both my machine & another server here in the office. I can create and pull the data fine...

Hi, I have been searching through the newsgroup for similar and relevant isdn bri layer 2 issues, and did come up with some hits. I just wanted to confirm some things as I'm not getting much joy...

Thank you ~ Let us linux ~ -----= Posted via Newsfeeds.Com, Uncensored Usenet News =----- http://www.newsfeeds.com - The #1 Newsgroup Service in the World! -----== Over 100,000 Newsgroups - 19...

I have two 2501's hooked up back to back via the serial connections. Problem is on one port the interface goes to an up/down status and does not work. The same exact config on the other serial...

I've got a strange problem with a Cat3524XL which boots absolutely fine and can be managed by it's normal IP address or it's cluster management IP address. But after a short while (several minutes to...

We are totally baffled by a problem we have been having ... here is what is happening ... - We have a Dell PowerEdge 650 running Redhat Linux 7.3 - And a CISCO firewall That's the only standard I...

Hi all...I am trying to figure out how to send x25 over a tunnel that is created by VPN appliances outside the cisco hardware (Symantec). Currently, an x25 nest is occupying one of the serial ports...

"News Account" <none@none.com> wrote in message news:<8NL9c.7387$ol3.1793@fe03.usenetserver.com>... Hi, I am unsure what version software on the PIX youare using but on 6.3 their is a command...

I need to have a W2000 server connect to a database on a remote machine with no user intervention. We have a Cisco concentrator at the remote site where the database is located. Using Version...

I have a Cisco 2611 installed with the Firewall feature set and I have initially configured it for NAT access with none of the Firewall features enabled and it has worked fine. I used the Cisco...

I know I have done this before, yet I keep getting an error when I try to copy flash tftp. It reaches my machine with the TFTP server on it, and it seems to be trying to copy it over, but I keep...