-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 The following config runs on a 3620 with a frame relay circuit and an atm/dsl circuit. Load balancing is done with multiple default routes and 'no ip...

Our company has packet size problem with some remote clients over the Internet. We find that when the packet size bigger than 120bytes, there will be 2-10% packet loss (both tcp/icmp) but never has...

Hi- I'm trying to use the VPN wizard on my PIX to create a site-site VPN but it asks me for a peer IP address. The router that I want to connect to it gets its IP through DHCP. Is this possible to...

Assuming a network with multiple switches, and multiple VLANs (that span across these multiple switches), with a per-VLAN STP. There is a separate MIB for each VLAN with the dot1dStpPortEntry....

Hello, I have a cisco 827 router with adsl modem, and I try to configure it but, the connexion to internet works,, and the router can ping to an internet host, but from any pc of the network, i...

I have problem with my 2600 router. I was trying to upgrate my IOS. I downloaded the router IOS into my my TFTP server and i errased my Router IOS from the Flash. When i reboot my router the ROMMON...

We have a PIX506e, and about 25 remote users that use the Cisco VPN Client (3.5.1). We have never needed them to be authenticated on the domain before, but I now I need to give them access to network...

I have a X25 ATM connecting to a router. I also have a server that connects to the ethernet interface using IP. I want to send traffic from the X25 device, translate it to IP and then send it to the...

Greetings, on an AS5800 how do I route all IPs that people aren't currently dialed up to to NULL0 (or the equivalent)? For some reason we seem to be getting routing loops when people aren't...

What is the tech-prefix command in gateways and gatekeepers in VOIP useful for thanks

Hi, there's a new feature in PIXOS 6.3(3) called Policy NAT. Now it should be possible to nat your source adresse against the destination. I need to permform a adress translation before the...

I am looking for a terminal server product that can map each serial port on the terminal server to a unique IP address. My application for this is management of several network devices through a...

How do I enter a range of ip-addresses I want to allow access? I need to allow a set of ip's from *.*.*.53 to *.*.*.65 but there doesn't seem to be a way of doing that. It seems to want an address...

One of our customers has a Cisco PIX 515 with PIX version 4.4(5), compiled on 23-May-2000. This version does not support vpdn, so i need a newer version. Show version only gives me the amount of RAM,...

Hello, does somebody new what happens or maybe has similar negativ results? And also maybe can give me a hint what I can do or change? I work on a migration from a FW1 Checkpoint and Cat65xx ACLs to...

Inherited a Pix 515. it has 5.2. Is there any reason not to install 6.3.3? Any gotchas? Can I still use the same activation key as I have now when doing a show version? or do I need a new...

Hi guys- I'm new to routers and I'm trying to get a 831 to connect to a PIX, but I want to it create a split tunnel so that only traffic meant for 192.168.0.0 255.255.255.0 is sent over the tunnel. ...

All I had tried Taiwan "Welltech" fxs, it work fine, but i had tried other taiwan fxs terinal gw, but won';t work with this the following is the debug of q931 of NOT success call $$ the ...

I need some assistance. All I need is for one network to ping th network of the other side through a pix ipsec tunnel. after the ping i want one network to join a windows domain of the other...

I have several contracts for smartnet on routers and firewalls under my own cisco ID I got when I first became CNNA. And now every time I order from my reseller, 'magically' the new contract is ready...