Hi all: I have a Catalyst 6509 witch WS-6348-RJ-45 cards. In last weeks I had several problems witch switches. In log messages apears this error: %SYS-3-SYS_LCPERR3:Module 7: Coil Pb Rx Underflow...

Hi everyone, running IOS FW feature on a 1700 series router and would require access to an internal server running PCA. The router is running NAT for me and the proposed config was: NAT statements...

Has anyone looked into using the new HP/Cisco 9216 type San switch with IP services card over a T-3 to replicate a volume..? With the bandwidth of a T-3 at 20BG/Hour uncompressed it should work for...

Hi there, I have some problems to configure an IPSEC-Tunnel with ISDN-Backup using dialer-watch. In the first location I have an 1750 with ETH0 to the provider-router, ETH1 to the internal network...

Hi, on my Catalyst 6500 I configured a vlan2 and added two ethernet ports to it. Then I defined a virtual vlan2 interface on the msfc module. The devices on each vlan2 port can ping one...

Hi all, I am having problems accessing a network via ISDN dial-in Cisco 2611 +------------------------+ Gateway: 10.1.1.1 PC -------( ISDN )-------| BRI0/0 Eth0/0 |------( LAN...

Hi everibody. I have a VoIP problem with AS5350. I successfuly can establish a call from PSTN. On the opposid side I have an IVR application (based on IBM's J323 Engine). When the call is...

Are the AGS and MGS's run 8.0xx code vulnerable? There are 80 of them behind a PIX 10000

I currently have an 827 ADSL router that I want to apply a priority list on the Dialer Interface. In itself and from all I have researched this should not prove as difficult as it has been.The main...

I've got a problem with my Cisco Catalyst 2924M XL. When I want to boot from the flash memory I get the following error...

I have been working on a particular bothersome problem for about a month now and I don't think I have come any closer to solving the problem... My 1605R is the standard Eth0 / Eth1 setup, no wic in...

wrong posting ? i suppose "Nacho" <ivalls @teleline.es> wrote in message news:qNASa.420041$iM4.642003@telenews.teleline.es...

Hello, Amy! You wrote on 20 Jul 2003 20:28:45 -0700: AL> I have a question regarding the SFP connectors on the Cisco Catalyst AL> 3750G-24TS-24 Ethernet 10/100/1000 ports and 4 SFP uplinks. AL> I...

On Sun, 20 Jul 2003 07:42:03 -0700, Thomas Perl wrote: ! interface Ethernet0 ip address 192.168.10.1 255.255.255.0 ! access-list 23 permit 192.168.10.0 0.0.0.255 ! line vty 0 4

Is there a way aside from using Websense and N2H2 to have a Pix force http traffic redirect to a proxy server upstream? I know this can be done easily with policy routing on IOS, but can this...

someone wrote: They're basically packets which arrived incomplete for some reason - usually they are too-short.

I'm pretty new to this so I'm hoping that my question and the answer to my problem are simple... The other night we lost power for a while and the next morning, several ports on our 2950 switch were...

jAndrew Coaton wrote: 5.2.3 is the earliest version showing at http://www.cisco.com/cgi-bin/tablebuild.pl/pix You are correct, upgrading without a contract is not free. Additionally, if buying used...

I've got the following situation: 2 sites one site with a 826 adsl router which gets a dynamic ip. (site 1) one site with a 1721 router (incl adsl and eth wic) which has a static ip. (site 2) Both...

In article <3f19cd6b$1@shknews01>, Azure¢« <no@no.com> wrote: First of all, wouldn't that .0 address be a network address and not a host (or router) address? Second, since you've just told the...