When using the outside interface as your IP you need to use the interface command rather than specifying the IP example: static (inside,outside) tcp interface www 192.168.1.9 www...

On Sun, 20 Jul 2003 09:49:13 -0700, PJC wrote: http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080093f31.shtml ip nat inside source list 7 interface serial 0...

On Thu, 17 Jul 2003 22:16:55 +0800, <azani@homecomm.net.my> wrote: Use protected...

What are the masks of the routers? Munzir Khalid Khan wrote:

anyone seen the ipv4 xploits ? Too many rumors in irc. hans

Thanks Jim and Oscar, I have look all over the net, but as we all know if you don't ask the right question you get the wrong answer,so thanks for the tip's.

I hope someone will be able to help me. I have a 1605 router that I have managed to completely mess-up. I have a limited knowledge of the device and the old saying holds true. I was attempting to...

Are DMZ zones suppose to be Internet address or can it be a 172.16.XX.XX?

Hi I have a Cisco 2503, 1601 R and a 4500 with 8 serial's and 1 Ethernet. I am looking for step by step Configuration info on how to set up routers from scratch. I am new to Routers, if you know of...

I am trying to configure an 827 ADSL router to act as a PPTP server for a W2K client. I have done this on a 2600 with no problem, but using the same config on the 827, the Windows client hangs on...

"Jim" <jimzjimmy@hotmail.com> wrote in message news:wMeSa.6546$5e7.438687@news20.bellglobal.com... Here's some reasons: 1) Your worried about being fired because you have nothing to do and you want...

Just upgraded IOS on this 3620 which was previously running, 12.0(7)XK2 It's config-reg was 0x3922. Before the upgrade I changed the config-reg to 0x2102, or so I thought. It took the config-reg...

I had the same problem. I could initiate a call from the inside network and it would work fine. When I tried it from the outside network, it would just time out. So I fired up "debug ip nat h323"...

Hi there.. I have a c3550 with a number trunked ports to c2950's off it for customers networks. On the 3550 I have multiple vlan's on it and the vlan's go to the 2950's. (the 3550 is basically a...

I aquired a cisco 4000 +M router with the following modules installed. FDDI module (two) np-2e ethernet modules When I boot the router : System Bootstrap, Version 4.14(7), SOFTWARE Copyright (c)...

Has anyone been able to successfully create a call transfer with call transfer commands? Leon McCalla leon#caribbeanlink.com (replace # with @ to send me e-mail)

Hi, I'm trying find a cheap (contradiction in terms) Cisco Switch (of if necessary combination of switchs) that will allow me to aggregate 4 fiber gigabit adapters in a server to multiple copper...

"Jim" <jimzjimmy@hotmail.com> wrote in message news:wMeSa.6546$5e7.438687@news20.bellglobal.com... The classic answer is "it depends" - decide what you want the network to do, and what features you...

"Jorish" <jorish@here.nl> wrote in message news:<bf3i90$gi1$1@phys-news-1.colt-telecom.nl>... By default those 16 interfaces are assigned to interface vlan 1. Put the IP address on that interface.

Hi, we have one Catalyst 4006 and serveral Catalyst 2950. They work fine but from my point of view there is one problem: If we set the speed and mode of the ports to auto negotiate then there is...