We currently have 2 sites connected via dark fiber with catalyst 3524 and GBIC's in trunk mode running multiple VLAN's across. I have a need to extend a T1 from one site to the other. I have been...

Hi I am working with Unix guy and he asks me if it is possible to put two ports two gether. Since there are two NICs in Unix and he can assign one IP to two NICs and hook them up to switch. So...

Sirs: We have a CISCO VoIP Network to provide IP telephony to our customers. The CISCO VoIP Network is interconnected to PSTN over E1 lines using 5850 gateways. We want to provide dial-up Internet...

Hi, An article at nwfusion.com states the following (24/6/2003): "Cisco is also releasing a scaled-down version of its CiscoWorks software that could be used to manage smaller networks. The...

Hey, Anyone had anyjoy with this setup? I am thinking of giving it a try. I've seen on the web that it can be done. Empok

Hi everyone, we just received a 837 router from an ex customer who thought they would be quite clever by deleting everything off it! Now it boots into Rommon. I have a couple of images for it but...

I have a user who is using Cisco VPN client for win2000 and he's connecting to our VPN. He can successfully establish the tunnel, and after doing so, he is able to connect to the exchange server...

In article <3f0ef193$0$29693$fa0fcedb@lovejoy.zen.co.uk>, Alex <nospam@hotmail.com> wrote: :I've already established up a VPN between a PIX 501 and another (non Cisco) :firewall. Both firewalls have...

"Sam Soh" <indotears@yahoo.com> wrote in message news:69c0a134.0307110838.774c3ea3@posting.google.com... Yes, here in Europe we run everything off of 220 Volts. The power supply in the Cisco 2500 is...

Hey, We got some of the 3725s in when they were quite new, and didn't support the NM-4T. As a result we used a combination of nm-2ws and wic-2ts as well as the native wic slots to get around...

I have a Cisco 2621 router that connects to a Allied telesyn fiber switch. I would like to segment my network into vlans/subnets however considering i only have one router it might be hard to do. ...

I work for a small ISP and we went to setup a HTTP cacheing server. I was told we needed to configure our router to forward port 80 requests to so and so ip address to let the server handle web...

Yup, done all the time. Watch the wrap: http://www.cisco.com/en/US/products/sw/secursw/ps2308/products_configuration _example09186a0080094680.shtml -Brian "Stefan Gasteiger" <stefan@gasteiger.de>...

In article <ddf83aad.0307090527.289abcf3@posting.google.com>, paul tomlinson <paul_tomlin@hotmail.com> wrote: :We have a site connected back to the web through a PIX 506 over a 2mb :DSL line, I'm...

Z wrote: --- / 1 \ With the connector from the PS facing you the pinouts are: |3 2 | 1 minus 2 plus 3 not used ------ Aironet 5v 1.6amp PS

I am unable to get my Cisco 804 ISDN router to answer incoming voice calls when the line is previously engaged in a data call. It will answer voice when NO data call is engaged. It will allow...

"Joe Barrett" <barrettj@wam.umd.edu> wrote in message news:Pine.SOL.4.44.0307110725001.5301-100000@rac1.wam.umd.edu... There isn't a lab to qualify for CCNA. Just one PC based exam. Chris.

There is this pix firewall (501), and i want to pptp to a server behind that firewall. i found an example configuration at the cisco website: In this configuration example, the PPTP server is...

What lab? (Check out the Boson simulator) Michael Hall CCNP "Joe Barrett" <barrettj@wam.umd.edu> wrote in message news:Pine.SOL.4.44.0307110725001.5301-100000@rac1.wam.umd.edu...

Is it normal for this to happen? Upstream provider routs IPs to me. I don't put a route in my router for those IPs. My pipe gets flooded by traffic going around in circles between my upstream and...