On May 30, 3:35 pm, deano <deangr...@hotmail.com> wrote: Probably. Lets say you had 1.1.1.0/24. Take your external interface, and instead of making it 1.1.1.2/24 (I assume .1 is your provider),...

This turned out to be a "well duh" on my test bench I only had the inside interface plugged in to do the configuration but it turns out that the interface has to be up in order for the cisco the even...

On May 30, 2:58 pm, deano <deangr...@hotmail.com> wrote: Well, you can leave logical vlan 204 where it is, but move the devices that you need to have external IPs to a switch hooked up outside...

On May 30, 2:42 pm, deano <deangr...@hotmail.com> wrote: You could bridge the outside into the inside, but then I'm not sure NAT would work then. If I understand correctly, you want to NAT to VLAN...

On May 30, 2:23 pm, deano <deangr...@hotmail.com> wrote: What is the IP range. As long as you can subnet it, yes you can carve out some addresses and others for static. However, your...

Tom Linden wrote: AT&T Router IP Address: 12.89.208.121 should clarify it. AT&T router means router under AT&T authority. So .122 is your side. You're AT&T's customer.

I manage freelance editors for Sybex books. If you'd like to be part of our industry-leading certification study guide team, I invite you contact me. For all of our cert books, we hire two...

http://pandaeatsbamboo.blogspot.com/2008/05/enable-world-mode.html

On 29 May, 18:11, Merv <merv.hr...@rogers.com> wrote: I am not in any sense complaining by the way - just wanted to mention ways to find out. Run wireshark/tcpdump/windump/other on a test...

On May 27, 1:35*pm, Al <ajsbu...@gmail.com> wrote: EasyVPN is a really good option for these scenarios. We use it for many sites that have smaller Cable/DSL based ISPs.

I curently have two ip block from the parent site. the first block is being NATed and is working on several Vlans. I wish to use the second block but have a one for one mapping for thes address...

-- --------------------------------- --- -- - Posted with NewsLeecher v3.9 Final Web @ http://www.newsleecher.com/?usenet ------------------- ----- ---- -- -

Lester Lane schrieb: This depends on how the device was resetted. cisco/cisco is the default for SDM configuration. If you delete all config there is no default ip address and no default...

In article <483e3a68$1@newsgate.x-privat.org>, Tosh <chebarba@gmail.com> wrote: Yes, looks like I read the documentation too quickly.

In article <53332cd3-86e3-4806-984b-8b17860925a4@m73g2000hsh.googlegroups.com>, Merv <merv.hrabi@rogers.com> wrote: Fresnel volume? ...

On May 29, 3:45*am, Bo...@hotmail.co.uk wrote: 3750 is IOS, therefore show mac-address-table

On May 29, 9:30 am, Paul Matthews <p...@cattytown.me.uk> wrote: All traffic is being translated by the ISA server so the CSS see it as one IP connecting and one...

On 28 May, 22:26, Jack <jba...@neustyle.com> wrote: As discussed above - does it fail over when you unplug the DSL instead - or even maybe shut the ATM interface. My memory is that dialers are...

On Wed, 28 May 2008 16:48:32 +0000, Stephen wrote: I have successfully used NTOP as a flow collector with an 1841. -- <http://ale.cx/> (AIM:troffasky) (UnSoEsNpEaTm@ale.cx) 19:10:04 up 10:51, 1...

Problem resolved; Finally the problem was on the server . A misconfigured registry was disabling the Path MTU Discovory , forcing the packet size to 536 for all non-local destination IP...