Hi there. We're getting a 10Mb Ethernet point to point connection between our office and a colocation datacentre. We are presented with an RJ45 cable at either end, and there is no routing involved...

Help....I currently run a crossover cable into my main computer to connect a spare to the internet....I was looking to add a laptop and wireless router...any chance I could keep the crossover cable...

I'm trying to setup an AS5400 for in/out modem/ISDN access, firstly I'd just like to configure for modem access, but when I dial into it I get the following output (debug isdn q931, isdn error & spe...

Hi, What kind of router, switches and access point are needed for a wireless infrastructure for about 10 users and the distance of 30 feet. Thanks...

Hi, Where can I find a good VLAN configuration howto for managed switches with examples...? regards Geir

I've sort of a problem, quite common but can't solve it :( I've PIX which uses certficate/radius authentication, it talks to a W2k3 Enterprise CA, everything works fine, the pix get's and certficate...

Hello all, I am looking to upgrade the IOS on my 6509. It has redundent sup 720's with a MSFC3A. 64MB Flash and 512 RAM. Currently it is running 12.2(17D)SXB2. Anyone have a recommendation...

I recently purchased a 1720 router and thanks to the help received here I have it up and running now. I have a wic-1enet on it. ios 12.39(c) I currently do not have it configured, it's not connected...

Hi all, I'm a newbie at cisco router. I have a 851W that's connecting 2 wireless devices to one AP. Unfortunately, since I've successfully configured the router, my two computer that connected...

1721 IOS 12.3(10) updated from IS 12.2 I've reset the router to factory defaults and am trying to install SDM ver 2.2a. I've ran the "username cisco privilege 15 secret 0 cisco" command and given it...

I have been searching Cisco's web site, but could not find a specific answer: could one use MLPPP between two 2812s, bonding one full T1 and one channelized (10 channels reserved for voice) T1? I...

I am having a hard time with this one so any help is needed and appreciated - I'm running out of options. I setup a Cisco 851w using the SDM gui. I'm not a CCNxxx anything just a lan admin but I can...

Will the Cisco 2620XM router accept an Ethernet WIC (WIC-1ENET=) ? The router has one fastethernet & one serial WIC. I cannot see an option for a "WIC-1ENET=" on the Cisco configuration tool. TIA,...

Everyone I ask, and every site I look for help on says: " I suggest you go to the cisco website and download PIX Device Manager (PDM). It is a free download for cisco PIX firewall." ARGH!!!!! I...

Hi All, I would like to create a separate vlan for all my vpn addresses, to keep them in a separate pool. is this bad practice? also, i am a little confused about how i would go about this because...

Hello every one , i have two connections one adsl(1544kbps) one frame relay(128 CIR) , i wanna have load balancing between this two connections i will have a 2811 router what i can do...

Hi, I have 4x E1 connections with 2 ISP. 2xE1 with ISP1 and 2xE1 with ISP2. I did the load balance putting the 2 default static routes in each router (My ISP did the same at their end, the load...

I am still trying to get this router to work properly (see also post of februari 10) and think the problem may lay in the fact that port 80 is not open. W4uWbHH@tpnet.pl> show ip pat Dropped - icmp...

Hi all, I had created IPsec VPN between so many sites. But not able to create a PPTP VPN Current situation is i want to create VPN for Hame users so that they can connect office using Windows PPTP...

I have a new client to set up. They have some equipment from an office that went out of business that I need to configure (very simple configuration). They have a cable internet connection to their...