Hello Trend, Thanks for your suggestion..I was just trying with available free ports to configure as a destination port as you said " ASICs serve every 8 ports (1-8, 9-16, etc). " it seems to be...

On Jun 21, 6:06*am, Merv <merv.hr...@rogers.com> wrote: There could be an issue with the memory as well... The new code may be using more memory. Memory that may not have been used in the...

On Jun 24, 8:10*pm, "J.Cottingim" <jcottin...@yahoo.com> wrote: JC, The traffic coming into the Fa4 interface IS being inspected on the IP address assigned to this interface (x.x.x.x), but it IS...

I use a Netgear 834G router and am trying to get the Status message to stay on the screen long enough for me to read it. Any ideas please TIA Brian

On Jun 24, 9:07 am, "terry...@o2.ie" <terry...@o2.ie> wrote: OK it is sorted... I had the Dialer interface on the router set up without "ip nat outside". It is unusual though, as once the router...

Is there a way for an ASA 5510 to set DSCP on packets? If not, how do I force each of the four physical interfaces to goto their "router" Here's our layout: ASA 5510 Port 0 -...

Ok how do we go about allocation of bandwidth given the requirements below, this is a pilot project and bandwith will be increased as needed. Thank you alexd wrote:

Hi, IndiaWeb/SoftGuard is supporting Cisco/Nortel/Enterasys/HP/... about 135 network component vendors so far. As it is used by car manufacturer Audi AG in large scale it was intended to use it at...

I recently removed a Checkpoint firewall at my host site and replaced it with an ASA 5250. All is going well, except for web traffic, which seems to be affected greatly by this change. All the...

Hi I going to create a lan-to-lan (ipsec) to a third party, but they will not accept our ip adresses, so i need to hide in my public ip adress does anybody have a ide , how to solve the case i was...

Valentin Guggiana wrote: Well, it worked the last few days. But today I had the same again. The arp entry was there because I set it statically but the 871 didn't reply to 'arp who-has' for this...

Charles Arnett wrote: Charles: Confirming that the content of this post is now visible with my newsreader. Best Regards, News Reader

On Jun 19, 4:36*pm, tman <naves....@gmail.com> wrote: nat (dmz) 1 0.0.0.0 0.0.0.0 needs to change to nat (dmz) 2 0.0.0.0 0.0.0.0 global (outside) 2 interface

Howard Huntley <hhuntleyjr@comcast.net> writes: Ya know, I'll bet Cisco could provide install...

Air Max 87 / 90 / 95 / 97 / 360 / 180 / 2003 / 2008 / TN / LTD Sneakers, Shox R2 / R3 / R4 / R5 / R6 / OZ / NZ / TL / Turob / BMW Sneakers Discout Puma Trainers, Adidas Trainers, Lacoste Trainers, ...

Probably the code you are running doesn't support it. I think you need 12.4. A "show diag" will always tell you if the hardware you have installed is supported by your software. Unsupported hardware...

I installed the NM and the VIC but do not get anything when I try and conifgure the voice ports. oip-rtr(config)#voice-port ^ % Invalid input detected at '^'...

www.efootjoy.com – prada sandals prices, reviews,wholesale jordans ,prada,fendi shoes and ratings in Clothing and Accessories . Compare products and find the lowest prices on crown air prada...

I'm trying to gain access to vlans at a remote ATM-connected site and assign them to ports on a switch at a central location. I need to do this for about 10 remote sites, one at a time. I was told...

On Jun 19, 11:05 am, smokinpope <keystro...@gmail.com> wrote: Smokinpope, A few thoughts... RFC 1490 is specific to Frame-Relay. - So I'm assuming your DS3 is configured for frame-relay. If you...