Hello.. first and foremost - I'd like to thank everyone in advance for taking the time to read and help with my issue below.. To make the long story short.. I need to get a new Palm LifeDrive...

Hi, I'm new to using PIX and was wondering if anyone could help me with a question I have. I'm looking at the PIX config that has been left by a network admin and cleaned up by myself, and have a...

Find expired domains with the best software: http://www.antssoft.com The best domain names are already taken. But with expired domain software you can find the best domain names...

Hi there I have a big problem that is on my mind a long time now The scenario is as simplest as I can 123 be. 1760 with a serial, a DSL and an Ethernet interface Ethernet on LAN Serial 2Mbit on x...

You have an FastEthernet switching module for which all of the port are layer 2. If you want layer 3 Fast Ethernet ports you will have to get a diffeenthardware for the 2821. With respect to the...

hi all in his Secure ACS server (for windows) Cisco has this : Downloadable IP ACLs-Cisco Secure ACS version 3.3 extends per-user ACL support to any Layer 3 network device that supports this...

Hi, I've a cisco router connected to a ADSL internet line. This router is configured for NAT with overload on INterface Dialer IP address (that is dinamically assigned from our provider). now I need...

Is Cisco IOS defaulting to "no ip source routing" prior to IOS version 12.3? i.e is "ip source routing" enabled by default on Cisco IOS 12.0, 12.1 and IOS 12.2?

I have office and remote site both sides i have cisco pix 501 I want to create VPN site to site (pix to pix) and VPN access to office Is this possible? can i set a Server VPN (for users to be able...

Hello, Given a site to site VPN between two PIX 515. On a lab, I have an OpenBSD machine in between. VPN Auth: PSK. So, the PSK is not going to the wire as is but hashed. I have tcpdump on the...

Hello, I have an existing static pix to pix vpn between the UK and France and need now to add a dynamic vpn between the UK and Spain. The static vpn works great but I cannot get a dynamic vpn up and...

Hello, I want to run DMVPN with hub (3745 12.314T2) behind NAT and spokes (1812 12.3(14)YT1) configured with public ip addresses. "Standard" configuration doesn't work. Is that configuration...

We have a leased line at a location in Thailand hooked up to the internet and the Cisco 2501 keeps crashing. We have replaced every piece of hardware including cables, router, transceiver, switch,...

I have a Cisco 506 Pix with current IOS loaded. The router is clean ready to program as new and is fully enabled. Cox has given me a static IP that is supposed to be used to connect to the Internet...

HOW TO TURN 6 BUCKS INTO 6 THOUSAND! (WORLD WIDE) WARNING: READING THIS WILL CHANGE YOUR LIFE! I found this on a Bulletin board and decided to try it. A little while back, I was browsing through...

Hi All I have set up a tunnel between 2 IOS Routers A and B (1760 and 1841). A has a single FastEth interface, and B 2 of them, FE0/0 with the crypto map, and FE0/1 connected to my LAN. While...

Hello, I have several remote cisco routers and one pix. There are crypto map between all the routers routers. the access-list of the crypto maps between the routers permit access to the subnet of...

I have set up a 2811 with a DSL interface (BT) and have FE/0 attached to the local lan 192.168.0.0/24. I have been through the VPN wizzard and all seemed fine (Tested okay with the SDM). However,...

I have set up a 2811 with a DSL interface (BT) and have FE/0 attached to the local lan 192.168.0.0/24. I have been through the VPN wizzard and all seemed fine (Tested okay with the SDM). However,...

The following should be sufficient to enable you to set up a Cisco Switch. If you need anymore information please come along to http://www.Menkaura.com/Forum/index.php and I'll try to assist...