Tech Support > Computer Hardware > Storage Devices > How to map out bad sectors
How to map out bad sectors
Posted by CWatters on July 13th, 2006


What's the best way/prog to map out a few bad sectors so that I can make one
more backup before replacing the drive?

Ghost is reporting "Read sector failure, result = 1, drive = 0, sectors
49262215 to 49262279" and then aborts the backup. Ran it twice with similar
results.

Thanks.

Colin

----------------------------------------------------------------------------
-----

For info..

Task Log has this entry..

Disk Error Details
IDE Controller error:
Uncorrectable data error
Error 0x40
Device/Head 0xe2
Cylinder High 0xef
Cylinder Low 0xae
Sector Number 0x8e
Sector Count 0x39
LBA Sector 49262222

Everest/Smart data says...

[ SAMSUNG SP1213N (S00UJ10Y309162) ]

01 Raw Read Error Rate 51 100 100 1 OK:
Value is normal
03 Spin Up Time 25 100 100 5440 OK:
Value is normal
04 Start/Stop Count 0 100 100 45 OK:
Always passing
05 Reallocated Sector Count 11 100 100 0 OK:
Value is normal
07 Seek Error Rate 51 100 100 0 OK:
Value is normal
08 Seek Time Performance 15 100 100 0 OK:
Value is normal
09 Power-On Time Count 0 99 99 766975 OK:
Always passing
0A Spin Retry Count 51 100 100 0 OK:
Value is normal
0B Calibration Retry Count 0 100 100 0 OK:
Always passing
0C Power Cycle Count 0 100 100 26 OK:
Always passing
C2 Temperature 0 133 85 35 OK:
Always passing
C3 Hardware ECC Recovered 0 100 100 144355197 OK:
Always passing
C4 Reallocation Event Count 0 99 99 3 OK:
Always passing
C5 Current Pending Sector Count 0 100 100 0 OK:
Always passing
C6 Off-Line Uncorrectable Sector Count 0 100 100 0 OK:
Always passing
C7 Ultra ATA CRC Error Rate 0 200 200 0 OK:
Always passing
C8 Write Error Rate 51 100 100 0 OK:
Value is normal
C9 <vendor-specific> 51 100 100 0 OK:
Value is normal


Posted by Rod Speed on July 13th, 2006


CWatters <colin.watters@turnersNOSPAMoak.plus.net> wrote:

You can tell ghost to ignore bads.
http://service1.symantec.com/SUPPORT...98082612540625




Posted by Arno Wagner on July 13th, 2006


Previously CWatters <colin.watters@turnersnospamoak.plus.net> wrote:
You should use software that is able to ignore bad sectors instead.
dd_rescue may be an option.

Arno

Posted by Folkert Rienstra on July 13th, 2006


"Arno Wagner" <me@privacy.net> aka "Babblehead" wrote in message news:4hmg6mF94tuU1@individual.net
Like Ghost maybe?

Or just Ghost?



Posted by CWatters on July 13th, 2006



"Michael Cecil" <macecil@comcast.net> wrote in message
news:cotbb21orc9nqlu9jjls5gctf66m5gbp76@4ax.com...
"Rod Speed" <rod.speed.aaa@gmail.com> wrote in message
news:4hm9otF8bdlU1@individual.net...

Thanks Rod and Michael,

I'm using the original Ghost and will give it a go tonight. My next problem
will be finding out what files are effected by these corrupt sectors. It
dosent seem to be anything too critical but I guess you never know.

Regards

Colin







Similar Posts